Handyprobe HP3

TiePie engineering

Details

Differential input

The Handyprobe HP3 is equipped with a differential input with a maximum input range of 800 Volt DC (566 Volt RMS). Because of the differential input, it is not possible to create a short circuit to ground through the oscilloscope. The high input range makes it possible to use the Handyprobe HP3 without additional attenuators.
Yet, the large dynamic range also allows to measure signals in the mV range.

Fast streaming

The advanced driver technology makes it possible to measure a continuous stream of data from the Handyprobe HP3 to the computer, at a maximum rate of 10 MSamples/s. The maximum measuring time is only limited by the available space on the hard drive. The high sampling rate makes it possible to capture short events with high accuracy. It is also possible to monitor e.g. the line power for a very long time and afterwards view and analyze each cycle of the signal thoroughly.

Low noise measuring lead

The input of the Handyprobe HP3 is differential, which means that both sides of the input have a high impedance. There is no connection to ground as in conventional oscilloscopes which are used with coax cables and standard probes.

The special low noise Measure lead TP-C812A is developed for the Handyprobe HP3. It is very insensitive to external interfering signals. The two ends can be placed up to two meters apart, while picking up very little interference. With a conventional oscilloscope with standard probes this is not possible. The maximum distance between the positive side and ground of a standard probe is usually limited to approximately 20 cm. The Measure lead TP-C812A for the Handyprobe HP3 does not have this limitation. Measuring between two distant points is now no problem anymore. The Measure lead TP-C812A uses a heat resistant silicone isolation and shrouded banana plugs.

Ergonomic design

The Handyprobe HP3 is designed to fit nicely in your hand. Its housing is fitted with soft rubber areas that ensure a good grip on it. A wrist strap can be attached, to carry the Handyprobe HP3 or to hang it near the test setup.

Models

The Handyprobe HP3 is available in three models:
Handyprobe HP3-100 : 100 MS/s maximum sampling rate
Handyprobe HP3-20 : 20 MS/s maximum sampling rate
Handyprobe HP3-5 : 5 MS/s maximum sampling rate

Produktbeschreibung

Produktname
Handyprobe HP3
Produkttyp
Oszilloskop für PC
Zusätzlich integrierte Messfunktionen
Digitalmultimeter, Transientenrecorder, Spektrumanalyzer, Logger, CAN SPI, UART/RS-232 Busse dekodieren
Zertifizierung (Prüfungen, Zulassungen)
CE, RoHS, CAT II
Produkteinführung
2010

Signalerfassung

Anzahl der Messkanäle
1
Analogbandbreite
50 MHz
Abtastrate
100
Eingangsimpedanz
2.1 MOhm an 15 pF
Maximale Eingangsempfindlichkeit
200 mV full scale
Vertikale Genauigkeit
±0.3%
Auflösung
10 Bit
Maximale Eingangsspannung
800
Maßstäbe zur Vertikalablenkung von
50 mV/DIV
Maßstäbe zur Vertikalablenkung bis
200
Anzahl kalibrierter Festeinstellungen
12
Automatische Messungen
Maximum, Mean, Minimum, RMS, Duty Cycle, Rise/Fall Time, Frequency, Integral, Differential, u.v.a.
Betriebsarten
block mode und streaming mode
Automatischer Wechsel zwischen Chopper- und Alternate-Betriebsart

Zeitbasis

Dehnungsfaktor
beliebig
Zeitbasisgenauigkeit
0.01%

Triggersystem

Triggerquelle
Kanal, Freilauf, Software
Triggerschwelle
0.1% (10 bit)
Triggerart
automatisch, normal, single shot
Signalflanken +/-
Freie Triggerpegeleinstellung
Weitere Triggerfunktionen
Pre-/Post-Triggerfunktionen, Inside/outside window, AutoDisk

Bedien- und Beobachtungs-Funktionen

Kathodenstrahlröhre
Einblendung der Messeinheit

Speicher- und Bearbeitungsoptionen

Messwertspeicherkapazität im Gerät
1 MiSamples
Oszilloskop-Kopplung an PC
Oszilloskop-Auswertungssoftware für den PC
Multi Channel software, treiber und DLL alle frei ab zu laden; SDK für Matlab, LabView, C++, C#, Delphi, VB u.s.w.
Auswertungssoftware läuft unter welchen Betriebssystemen
Windows 98 ... Windows 10, 32 + 64 bit

Hardware-Eigenschaften

Breite
68
Höhe
25
Tiefe
177
Gewicht des Gerätes in g
290 g
Schnittstellen
USB 2.0 High speed (480 Mbit/s), USB1.1 compatible
Akku- / Batteriebetrieb
Netzbetrieb
Preis des Gerätes
448

Firma

TiePie engineering